1084 Blade Stock

In stock

1084 Annealed Medium-High Carbon Steel.

3/16" thick -  Gold color designation

1/4"  thick - Orange Color Designation

Lengths available - 12", 18" & 48"

Warping - a slight bend in material is completely normal, as our material comes directly from the Mill where it is rolled off a coil and the material might recall the natural curvature of the coil. Additionally, please note that cutting of the material will relieve the stress that is causing the bend. It is more than likely that the bend will correct itself as you move forward in your process.

**All 48" lengths of steel will be cut in half for shipping purposes**

 

Item #
1084 stock
Grouped product items
Product Name Price Qty

1084 Blade Stock - 3/16 x 1 x 12"
$10.00

1084 Blade Stock - 3/16 x 1 x 18"
$15.00

1084 Blade Stock - 3/16 x 1 x 48"
$35.00

1084 Blade Stock - 3/16 x 1.5 x 12"
$16.00

1084 Blade Stock - 3/16 x 1.5 x 18"
$20.00

1084 Blade Stock - 3/16 x 1.5 x 48"
$45.00

1084 Blade Stock - 3/16 x 2 x 12"
$18.00

1084 Blade Stock - 3/16 x 2 x 18"
$24.00

1084 Blade Stock - 3/16 x 2 x 48"
$55.00

1084 Blade Stock - 1/4 x 1.5 x 12"
$20.00

1084 Blade Stock - 1/4 x 1.5 x 18"
$25.00

1084 Blade Stock -1/4 x 1.5 x 48"
$55.00

1084 Blade Stock - 1/4 x 2 x 12"
$22.00

1084 Blade Stock - 1/4 x 2 x 18"
$28.00

1084 Blade Stock -1/4 x 2 x 48"
$60.00

1084 Annealed Medium-High Carbon Steel.

3/16" thick -  Gold color designation

1/4"  thick - Orange Color Designation

Lengths available - 12", 18" & 48"

Warping - a slight bend in material is completely normal, as our material comes directly from the Mill where it is rolled off a coil and the material might recall the natural curvature of the coil. Additionally, please note that cutting of the material will relieve the stress that is causing the bend. It is more than likely that the bend will correct itself as you move forward in your process.

**All 48" lengths of steel will be cut in half for shipping purposes**

 

1084 Annealed Medium-High Carbon Steel.

3/16" thick -  Gold color designation

1/4"  thick - Orange Color Designation

Lengths available - 12", 18" & 48"

Warping - a slight bend in material is completely normal, as our material comes directly from the Mill where it is rolled off a coil and the material might recall the natural curvature of the coil. Additionally, please note that cutting of the material will relieve the stress that is causing the bend. It is more than likely that the bend will correct itself as you move forward in your process.

**All 48" lengths of steel will be cut in half for shipping purposes**

 

1084 Annealed Medium-High Carbon Steel.

3/16" thick -  Gold color designation

1/4"  thick - Orange Color Designation

Lengths available - 12", 18" & 48"

Warping - a slight bend in material is completely normal, as our material comes directly from the Mill where it is rolled off a coil and the material might recall the natural curvature of the coil. Additionally, please note that cutting of the material will relieve the stress that is causing the bend. It is more than likely that the bend will correct itself as you move forward in your process.

**All 48" lengths of steel will be cut in half for shipping purposes**

 

All 48" lengths of steel will be cut in half for shipping purposes.  You can still purchase 48" lengths locally at our shop - PICKUP ONLY

1084 Annealed Carbon Steel.

Many beginners start with our 1084, It is a eutectoid steel

This blend of 1084 has been carefully adjusted so that forges and grinds easily, requires only the very basics of a simple heat treatment, and an ideal choice for makers both beginners and seasoned smiths alike. Since 1084 is a high carbon steel, it will rust and tarnish if not properly taken care of, so makers should warn customers of possible corrosion issues if they do not clean and oil blades after use.

Straight from our stock, our 1084 comes pickled and annealed, so makers can be assured that it will arrive ready and able to be forged or ground into a great blade, or used in damascus steel production.

Whether you want to make a kitchen knife, small every day carry, or that big honking zombie or camp chopper, you won’t be disappointed by our 1084’s ability to harden, offer good abrasion resistance, solid edge retention, and even the ability to hamon when heat treated well.

Normalization:
Normalization is a process intended to refine grain and stress relieve blades prior to hardening when needed.
Turco, ATP-641, foil, or similar may be used to reduce surface decarburization and scaling.
Time at temperature suggested for varying thicknesses. Once knife has cooled to black and magnetic, it can be cycled again--be careful handling hot blades.

Hardening:
ATP-641, Turco, or similar high temperature anti-scale/decarburization coatings can be used to reduce scale or surface decarburization.
Data is representative of controlled heat treating equipment (e.g. oven, salts, etc.) temperatures and industrial standard quenchant.
Suggested quench oil: Parks 50--expected as quenched hardness may be lower if a slower quench oil or non-industrial quench medium is used.
*Austenizing soak time varies 5 to 15 minutes based on heat treating equipment and cross section--soak times are reduced to minimum for people heat treating in a forge--forge heat treating without PID temperature control limits accurate means of maintaining temperature. If using calibrated, proper industrial equipment for heat treating, use the supplied extended soak times based on over all steel thickness.
**Do not put blades in oven when cold, insert at or just below austenizing temperature--temperature variances is for difference in stock thicknesses and a window of margin for error.
Austenizing temperature Hold/Soak Time Expected Rc (as quenched) 1,450 to 1,480°F / 801°C 5-15 minutes 64-65

Tempering:
Once blade is quenched and near ambient temperature, blades should be tempered accordingly, the times suggested are to ensure even, consistent temperature.
Figures supplied are as representative of industrial standards.
*If using a small toaster oven or household kitchen oven for tempering, using a blade holding rack made from kiln furniture, a roasting tray lined with fine sand, or similar large object will help retain thermal mass to reduce wide swinging temperatures as the device fluctuates trying to maintain temperature. Note: Final hardness values vary based on initial as-quenched hardness and percentage of conversion to
(1st cycle)
1,650°F / 898°C (10-15 min)
(2nd cycle)
1,500°F / 815°C (10-15 min)
(3rd cycle)
1,350°F / 732°C (10-15min)

Martensite. Only reliable testing methods, e.g. calibrated Rockwell hardness tester, can provide actual hardness values--hardness calibrated files and chisels are relative testing methods and inaccurate for
true hardness Temper twice
Temperature: 300°F / 149°C 350°F / 177°C 400°F / 204°C 450°F / 232°C 500°F / 260°C 550°F / 288°C 600°F / 316°C 650°F / 343°C
value reading. for 2hrs.
Hardness (2 hour x2 guideline): 65
63-64
60-61
57-58 55-56 53-54 52-53 50
***The included Heat Treat Schedule on this page is formulated based upon Industry standards and data from ASM International, Crucible and other foundry spec sheets, and Kevin Cashen (independent researcher, ferroalloy metallurgist, and bladesmith of Matherton Forge).
Suggested heat treatment are based on the recommended specifications for use in ovens, high temp salts, and similarly, properly calibrated equipment; and in line with proper industrial standards for quenching. Deviation from industry standards for schedules, equipment, quenching mediums; and hardness testing equipment may result in varied results. The supplied information on this page is on a generalized scale with the above mentioned standards and methods, which is why soak times and similar aspects may vary in time length to include a margin for the available heat treating equipment and steel cross section.
If you are unsure if you have the necessary means to heat treat on-site, we recommend professional heat treating services provided by Peters Heat Treat or Bos Heat treating; or industry specific services by knife material dealers such as TruGrit or Texas Knifemaker's Supply--check with suppliers to see if they offer HT services and ensure they follow industry standards.

Blacksmiths Depot is not liable or responsible if proper industry heat treating protocols are not applied; particularly and especially if sending to an independent heat treat provider if they do not follow the intended heat treat schedule or standards for that particular steel; or damage they cause while in their possession.

 

 

Write Your Own Review
You're reviewing:1084 Blade Stock
Your Rating